Technical parameters ofφ3.2×9m coal mill
一、Main technical parameters & performances
1. Sepc.:φ3.2×(6.75+2)m
2. Length of drying chamber:2m
3. Length of grinding chamber:6.75m
4. Grinding material: blind coal
5. Capacity:20-22t/h
6. Mill inlet raw coal grian size ≤25mm,Residue 2%, mill outlet coal powder fineness:80μm
7. Mill inlet raw coal moisture content≤12%,Outlet coal powder moisture content≤1%
8. Mill inlet air temperature <350℃ Mill outlet air temperature: 60-80℃
9. Rotating speed of mill:17.3r/min
10. Transmission type: edge driving
11. Max. ball load:54t
12. Filling rate:23.5%
13. Cooling water consumption of main bearing:2m3/h
14. Cooling water consumption of slide shoe bearing:3.5m3/h
15. Water consumption of thin oil station of main reducer: 5.7m3/h
16. Water consumption of lubrication device of slide shoe bearing: 3.8m3/h
17. Water consumption of lubrication device of main bearing: 1.5m3/h
18. Main motor: Type YRKK560-8 IP54
Power:710KW,
Motor voltage10KV
Rotating speed at full load: 741r/min
19. Main reducer: Type JDX630
Speed ratio:5
Input rotating speed:741r/min
20. Slow driving motor: Type Y200L-8 IP44 Power 15KW
Rotating speed at full load:730r/min Voltage:380V
21. Slow driving reducer: Type ZSY250-90-I Speed ratio:I=90
Disc rotating speed:19r/min Input rotating speed:730r/min
22. Cooling type: water cooling
23. High/Low pressure oil station of main bearing:XGD-A2.5/25
(1)Low pressure system:
Flow rate 25L/min
Oil supply pressure:0.5MPa
Oil supply temperature:40±3℃
Motor:Y90L-4 1.5kW
(2)Hihg pressure system:
Flow rate:3.5 L/min
Oil supply pressure:32MPa
Motor:Y100L1-4 2.2kW
(3) Oil electrical heater SRYZ-220/2 Power 2kW Voltage 220V
(4) Differential pressure transmitter CS-V-0.155W 220V,0.25A
24. High/Low pressure oil station of slide shoe bearing:XGD-A2×2.5/63
(1) Low pressure system:
Flow rate:63L/min
Nominal pressure:0.63MPa
Motor Y112M-6 Power2.2kW Rotating speed:940r/min Voltage380V
(2) High pressure system
Flow rate:2.5L/min
Nominal pressure:32MPa
Motor Y100L1-4 Power 2.2kW
(3) Oil cooler GLC3-10/0.63 Cooling area:10m2
Nominal pressure:0.63MPa Rotating speed:1430r/min Voltage 380V
(4) Differential pressure transmitter:CS-Ⅲ Power:0.055kW Voltage:220V
(5) Electrical heater:SRYZ-220/3 Power:3KW Voltage:220V
25. Total equipment weight:-t
( Total equipment weight is 129t except motor and reducer).
二、 Main spare parts and material quality
1、 Main motor YRKK560-8 710kW 10KV
2、 Main reducer JDX630-5
3、 Shell Q235-B δ=30mm Entire annealing
4、 Slide ring 20g-Z25
5、 Hollow shaft ZG230-450
6、 Main bush: Lower part HT250
Bush body HT250
Bush liner(巴氏合金Babbitt ZchSnSb11-6)
Bump ball base:34CrNi3MoA/45
Idler roller:45
7、 Liner: Chromium alloy
8、 Thin oil station XGD-A2.5/25/XGD-A2×2.5/63
9、 Control cabinet & start cabinet
三、 Supply range
1、 Rotary section |
1set |
2、 Feed device |
1set |
3、 Main bearing device |
1set |
4、 Slide shoe bearing device |
1set |
5、 Discharge device |
1set |
6、 Liner & diaphram |
1set |
7、 Transmission device (bull gear, pinion & transmission base, etc. ) |
1 set per pc |
8、 Main motor |
1pc |
9、 Main reducer |
1pc |
10、 Auxiliary motor |
1pc |
11、 Auxiliary reducer |
1 pc |
12、 Coupling |
1 set per pc |
13、 Base of motor & reducer |
1 set per pc |
14、 Thin oil station |
2 pcs |
15、 Gear cover |
1 pc |
16、 Control cabinet (full high pressure control, low pressure start, thin oil station control) |
1 pc |
Jiangsu Pengfei Group Co., Ltd
|